Skip to content Go to Accessibility Statement

User Manuals

Users Guide: PPE EN 388:2016 and EN 420:2003+A1:2009 Cat.2 Glove

These products are classed as Personal Protective Equipment (PPE) by the European PPE Regulation (EU) 2016 / 425 and have been shown to comply with this regulation through the Harmonized European Standards EN 388:2016 and EN 420:2003+A1:2009.

The user must select the appropriate gloves for the task at hand.
Storage and transport: When not in use, store the product in a well-ventilated area away from extremes of temperature
Obsolescence information: Inspect the gloves before use for tears or holes. If any are found do not use the gloves and dispose of them.

Cleaning instructions: The gloves should be wiped clean under lukewarm water only.
Allergy information: Gloves do not contain any harmful substances to the wearer
EN388:2016 Levels are based upon the table below:

EN 388:2016 glove rating chart showing abrasion, cut, tear, puncture, ISO cut test, and impact protection ratings,

EN 388:2016 chart description

This chart explains how to read the EN 388:2016 marking printed on protective gloves.

At the top is the label EN388:2016 above a shield-shaped pictogram showing a hammer, the symbol for protection against mechanical risks. Below the shield is an example performance code, 4X42CP. An arrow runs from each character of the code to the test it represents, and a Rating column on the right gives the possible results for each test:

  1. 1st character (4 in the example): Abrasion resistance, rated 1 to 4.
  2. 2nd character (X): Cut resistance, Coup test, rated 1 to 5.
  3. 3rd character (4): Tear resistance, rated 1 to 4.
  4. 4th character (2): Puncture resistance, rated 1 to 4.
  5. 5th character (C): Cut resistance, TDM test ISO 13997, rated A to F.
  6. 6th character (P): Impact protection, shown as P, F or X.

Higher numbers and later letters mean better performance. X means the glove was not tested or the test is not suitable for it. The example glove therefore has abrasion level 4, no Coup cut result, tear level 4, puncture level 2, TDM cut level C, and passed the impact protection test.

 

Performance Level

1

2

3

4

5

 

6.1 Abrasion resistance (cycles to failure)

100

500

2000

8000

N/A

 

6.2 Blade cut resistance (minimum cut resistance index)

1.2

2.5

5

10

20

 

6.4 Tear resistance (lowest peak force / N)

10

25

50

75

N/A

 

6.5 Puncture resistance (lowest peak force / N)

20

60

100

150

N/A

 

6.3 TDM Cut resistance

A

B

C

D

E

F

Newtons (N)

2

5

10

15

22

30

 

 

 

 

 





Level “X”: indicates that the glove has not been submitted to the test or the test method appears not to be suitable for the glove design or material 

Impact Protection: Where the gloves meet the requirements of EN 388 for impact protection the marking code “P” is added after the five performance levels. The test has been carried out with impact energy of 5 J. Impact protection has been tested and rated at the knuckle area of the glove only. Impact protection has not been tested and rated at the areas of the fingers.

Gloves are not suitable for chemical applications. 

If tear performance is greater than level 1, the glove shall not be worn when there is a risk of entanglement by moving parts of machines.
Glove Sizes (marked according to EN 420): 7, 8, 9, 10, 11, 12

Do not apply heat. New and used gloves should be thoroughly inspected for damage before use. Information regarding protection refers to the working surface, i.e “the palm side” of the glove, which has been submitted for testing. The protection levels indicated are only valid for new gloves.

Manufactured by: Ironclad Performance Wear, 3325 Roy Orr Blvd. Suite 200, Grand Prairie, TX 75050, United States

Phone: 844-200-5664
Email: Customerservice@ironclad.com
Declaration of Conformity can be found on website at [www.ironclad.com/certificates &nbsp](https://www.ironclad.com/certificates &nbsp);

The following are exclusive trademarks of BRIGHTON BEST INTERNATIONAL, INC:  
KONG, IRONCLAD, IRONCLAD PERFORMANCE WEAR, and the IRONCLAD logo.  
Any unauthorized use is strictly prohibited and will be prosecuted to the fullest extent of the law.